Canada post shipping rates

https://www.canadapost-postescanada.ca/cpc/en/tools/find-a-rate.page

A book, small 20-30$

A book, large 18-30$

10lbs, $50

Put all the mp3s in a folder and open Terminal in that folder and do:

for f in *.mp3; do ffmpeg -i "$f" "$(basename $f).wav"; done

However, this will produce filenames like originalName.mp3.wav. This will cause errors on SD cards, and you might have to reformat the SDcard (it will lock all the files and folders as 'read only'.)

srm -rlvz to delete a directory, like ‘srm -rlvz DIRNAME’ (r) recursively (dir and all it's contents), (l) overwrites only 2x not default 38x, (z) then with zeros, and shows progress (v verbose).

The standard way is just

srm -f myfile.txt

(f is a single pass)

or

srm -r -v myfolder/

...

USE SFILL (part of secure-delete package) to overwrite unused 'available' space.

Note that sfill is not 'preferred' for SSD drives (it is fine for oldschool disk drives) because it causes wear to SSDs, and another method may be preferred, TRIM method, which Kali already runs once per week, but you can make it more frequent, method described below).

Anyway, here are the sfill commands:

1 pass version: sudo sfill -llv /home/yourusername

(-v is for verbose so you can see it working)

38 passes, slow, scrubbed version: sudo sfill -v /home/yourusername

Sfill will wipe all free space on the partition containing that folder. It will just create a file/files called like 000000 or something, and they will keep getting bigger until they take up the entire available space, and then the file/s will disappear.

If your have an SSD (not an old-school magnetic Hard Drive), you should be careful with these tools.

Wear and Tear: SSDs have a limited number of "writes." Overwriting free space is a massive write operation that can shorten the life of your drive.

TRIM is better: On modern SSDs, the fstrim command is usually more effective and safer. It tells the SSD controller to physically wipe the deleted blocks without the heavy "overwriting" process. sfill is very slow, but trim just takes seconds. Trim is considered 'standard maintenance' and doesn't wear the SSD drive, unlike sfill which does wear out the drive. Data is still 'unrecoverable' on 'most modern SSDs)

On an SSD, data isn't just "forgotten" when you delete a file; it stays in the memory cells until the drive's controller decides to wipe them to make room for new data. fstrim tells the controller, "These specific blocks are empty—go ahead and wipe them now."

Run TRIM with: sudo fstrim -av

-a (All): Tells the program to check all mounted partitions that support TRIM (like your root / and home /home partitions).

-v (Verbose): This provides feedback. It will tell you exactly how many Bytes (or MB/GB) were successfully discarded/cleaned.

Most modern Linux distributions (including Kali) have a "timer" that runs this once a week automatically. You can check if yours is active with: systemctl status fstrim.timer

By default, Kali does this weekly. You can change TRIM schedule to daily with:

sudo mkdir -p /etc/systemd/system/fstrim.timer.d && \
echo -e "[Timer]\nOnCalendar=daily\nAccuracySec=1h" | sudo tee /etc/systemd/system/fstrim.timer.d/override.conf && \
sudo systemctl daemon-reload

What this command does:

mkdir -p ...: Creates the folder where systemd looks for custom settings (overrides).

echo -e ... | sudo tee ...: Writes the "daily" instructions into a new file called override.conf.

systemctl daemon-reload: Forces the system to read the new settings immediately.

How to verify it worked: Run this command to see your new schedule: systemctl list-timers fstrim.timer ... You should see the NEXT column showing a time within the next 24 hours.

• Manjaro VM (after doing install inside the VM, remove the Manjaro iso from the VM's Settings > Storage
• You need AUR (not preinstalled on Manjaro): To enable AUR on Manjaro, launch Pamac and click on the three vertical dots at the top right-hand corner. Click on Preferences and enter your password, when prompted. Navigate to the Third-Party tab. In the AUR section, enable the Enable AUR Support toggle. Let the system auto-refresh for the changes to incorporate. (takes time maybe?) and check off those under there.
• from the AUR in package manager, download python2-gimp

https://www.youtube.com/watch?v=hdI2bqOjy3c

2 ways to put javascript on a page

<scripttttttt>alert('Hello world');</scriptttttttt>
a second file, called main.js
No need for <scripttttttt> tags because it's in the js file, so just put
alert('Hellow world');
Done

To view this in the browser, you want Console (tab) in Developer Tools for whatever browser

You can type javascript in it, like

alert(1)

and it works

VOCABULARY The DOM is the user interface (selecting elements), as separate from the Console where actions are performed.

const = can't be changed (you can change the values of arrays variables etc though), and you have to put a value.

let = like an initial position